ELASTOSIL® RT 723 A/B
ELASTOSIL® RT 723 A/B is a non-slump, addition-curing, 2-part silicone rubber for CIPG and FIPG applications. The product vulcanizes at elevated temperature to yield a a permanently flexible silicone rubber with very good mechanical properties and very low compression set.
Cured ELASTOSIL® RT 723 A/B shows very good adhesion to many substrates and long-term stability against weathering, moisture and UV light. The cured silicone rubber may continuously be exposed to constantly changing climatic conditions, UV radiation and temperatures as high as 230 °C (446 °F) without damage.
Eigenschaften
Uncured:
- 1 : 1 mixing ratio
- Non-slump paste
- Fast curing at moderate temperature levels
Cured:
- Medium hardness
- Very low compression set
- Designed for CIPG applications, but also suitable for FIPG (sealing & bonding)
- Good resistance to fluids, lubricants, cleaning agents, alcohols and aqueous media.
- Electrically insulating
- Light & weathering resistant
- Recommended service temperature range: -50 °C to +230 °C
Spezifische Merkmale von ELASTOSIL® RT 723 A/B
- Additionsvernetzend
- hitzebeständig
- medienbeständig
- Schnelle Aushärtung unter Hitze
- UV-stabil
- zweikomponentig
Datenblätter
- General-purpose CIPG grade, in particular for applications with occasional contact to liquids
- General-purpose FIPG grade for technical applications
- Typical fields of application: automotive, mechanical engineering
Important!
Only A and B components with the same batch number should be processed together!
Surface preparation:
All surfaces must be clean and free of contaminants that will inhibit the cure of ELASTOSIL® RT 723 A/B. Examples of inhibiting contaminants are sulfur containing materials, plasticizers, urethanes, amine containing materials and organometallic compounds – especially organotin compounds. If a substrate’s ability to inhibit cure is unknown, a small scale test should be run to determine compatibility.
When a substrate is known to pick up ambient moisture, e.g. as technical polyamide grades usually do, it is recommended to reduce the level of absorbed humidity by drying the substrate at 120 °C prior use. This minimizes the risk of bubble formation at the silicone/substrate interface during the curing process.
Mixing:
Caution ! Component A of ELASTOSIL® RT 723 A/B contains the platinum catalyst, component B comprises the crosslinker. Since even traces of platinum catalyst may cause gelling of component B, all tools (e. g. spatula, stirrers, mixing cups etc.) used for handling either component A or the A/B mix must not come into contact with component B by mistake.
The two components should be thoroughly mixed at a 1 : 1 ratio by weight or volume, preferably by automatic metering lines equipped with static or dynamic mixing devices.
Curing:
The curing time of addition-curing silicone rubber is highly dependent on temperature, size and heat sink properties of the respective substrates or of the assembly parts to be bonded, respectively. In order to secure a quick build-up of adhesion to the substrates, ELASTOSIL® RT 723 A/B is vulcanized between 120 °C and 200 °C usually. Typical curing temperatures and resulting curing times are given in adjacent table.
Detailed information about processing 2-part addition-curing silicones is given in our brochure “ROOM TEMPERATURE VULCANIZING (RTV) SILICONES - MATERIAL AND PROCESSING GUIDELINES”. We recommend running preliminary tests to optimize conditions for the particular application.
Removal:
If removal of the silicone from machines or dispensing equipment is necessary, white spirit or similar nonpolar solvents are recommended. However, cleaning ideally should take place before the silicone is fully vulcanized. Cured silicone rubber needs to be rubbed off or removed mechanically, if necessary in combination with a swelling agent (solvent) or a chemical silicone remover.
Lagerung
Store in a dry and cool place.
The 'Best use before end' date of each batch is shown on the product label.
Storage beyond the date specified on the label does not necessarily mean that the product is no longer usable. In this case however, the properties required for the intended use must be checked for quality assurance reasons
Vertrieb & Support
Wie können wir Ihnen helfen?
- Benötigen Sie Unterstützung bei der Produktauswahl oder wünschen Sie eine technische Beratung? Kontaktieren Sie unsere Experten.
Distributoren
WACKER verfügt weltweit über ein Netzwerk fachkundiger Vertriebspartner. Bitte wählen Sie noch eine Anwendung aus damit wir Ihnen Ihre Ansprechpartner nennen können.