ELASTOSIL® E6 N CSC
ELASTOSIL® E6 N CSC is a flowable one-part silicone rubber for potting or coating applications, and it is in particular suitable the for surface impregnation of porous natural materials. When exposed to air moisture the product cures at room temperature to yield a permanently flexible silicone rubber with good mechanical and release properties.
Fully vulcanized ELASTOSIL® E6 N CSC shows long-term stability against weathering, moisture and UV radiation. The silicone elastomer may continously be exposed to constantly changing climatic conditions, UV radiation and temperature as high as 180 °C (356 °F) without damage.
Eigenschaften
Uncured:
- Flowable
- Fast skin formation at room temperature
- By-product of curing: acetic acid
Cured:
- Medium hardness
- Recommended service temperature range: -50 °C to +180 °C
- No inhibition of Pt curing silicones
- Good resistance to liquid media, in particular to water or water-based compositions comprising alcohols and/or carboxylic acids
- Suitable for applications with food contact.
Please note:
fully cured ELASTOSIL® E6 N CSC is suitable for uses under the Recommendation "XV. Silicones" of the BfR and 21 CFR § 175.300 "Resinous and polymeric coatings" and FDA 21 CFR §177.2600 "Rubber articles intended for repeated use", provided that any given limitations on extractable and volatile substances are observed. Residual solvents have to be completely removed from the food contact article
Spezifische Merkmale von ELASTOSIL® E6 N CSC
- bietet ausgezeichnete Wasserabweisung
- einkomponentig
- elektrisch isolierend
- kondensationsvernetzend
- lebensmittelverträglich
- lösemittelfrei
- niedrige Viskosität
- UV- & verwitterungsbeständig
Datenblätter
ELASTOSIL® E6 N CSC is primarily designed for the coating and the surface impregnation of natural materials, such as wood, wooden materials, cork, paper and paperboard. Treatment with ELASTOSIL® E6 N CSC creates a smooth and soft-touch surface finish.
ELASTOSIL® E6 N CSC is a ready-to-use, one-part silicone rubber which starts curing when exposed to air moisture. Typical curing characteristics are given in the table "Properties Uncured".
As RTV-1 silicones require humidity for curing, free access of air moisture to the silicone rubber is essential. Additionally, the vulcanization time of ELASTOSIL® E6 N CSC can be greatly reduced by increasing the level of air's relative humidity. Please note that, unlike the initial skin formation, the total curing rate of RTV-1 silicones is limited by moisture's diffusion speed in silicone rubber.
As increasing the curing temperature has just a minor effect both on the skin forming time and the curing speed, ELASTOSIL® E6 N CSC typically is vulcanized at room temperature. Heat curing is recommended only for applications where the silicone rubber is applied as a thin film (thickness less than 0.5 mm), because otherwise blistering is likely to occur due to the quick release of acetic acid.
Due to its excellent flowability ELASTOSIL® E6 N CSC can be processed by any conventional coating method, e.g. by dipping, spraying, jetting, knife coating or dispensing.
After completion of the vulcanization the silicone elastomer remains permanently flexible over a wide temperature range. Cured ELASTOSIL® E6 N CSC can continuously be exposed to constantly changing climatic conditions, UV radiation, and aqueous media without damage. Besides, ELASTOSIL® E6 N CSC usually shows good primerless adhesion to many substrates, e.g. glass, ceramics, metals, plastics, powder coatings and materials based on paper, wood or cork.
Detailed information about the processing of RTV-1 silicones is given in our brochure “ROOM TEMPERATURE VULCANIZING (RTV) SILICONES - MATERIAL AND PROCESSING GUIDELINES”. We recommend running preliminary tests to optimize conditions for the particular application.
Removal:
If removal of the silicone from machines or dispensing equipment is necessary, white spirit or similar nonpolar solvents are recommended. However, cleaning ideally should take place before the silicone rubber is fully vulcanized. Cured silicone needs to be rubbed off or removed mechanically, if necessary in combination with a swelling agent (solvent) or a chemical silicone remover.
Lagerung
Store in a dry and cool place.
The 'Best use before end' date of each batch is shown on the product label.
Storage beyond the date specified on the label does not necessarily mean that the product is no longer usable. In this case however, the properties required for the intended use must be checked for quality assurance reasons.
Vertrieb & Support
Kolkata 743503
Indien
+91 33 24072-502 (Fax)
Wie können wir Ihnen helfen?
- Benötigen Sie Unterstützung bei der Produktauswahl oder wünschen Sie eine technische Beratung? Kontaktieren Sie unsere Experten.