Dieser Inhalt ist für Uganda bestimmt. Unser System hat erkannt, dass Sie aus USA kommen. Wollen Sie USA als neues Land setzen?
ELASTOSIL® E43 N TRANSPARENT
ELASTOSIL® E43 N TRANSPARENT is a one-part, non-slump to self-levelling silicone adhesive. When exposed to air moisture it cures at room temperature to yield a permanently flexible silicone rubber with very good mechanical properties.
Fully cured ELASTOSIL® E43 N TRANSPARENT shows long-term stability against weathering, moisture and UV radiation. The silicone elastomer may continously be exposed to constantly changing climatic conditions, UV radiation and temperature as high as 180 °C (356 °F) without damage.
Eigenschaften
Uncured:
- Non-slump to self-levelling
- Fast skin formation at room temperature
- By-product of curing: acetic acid
Cured:
- Medium hardness
- Designed for bonding and FIPG applications
- Recommended service temperature range: -50 °C to +180 °C
- No inhibition of Pt curing silicones
- Suitable for applications with food contact
Please note: fully cured ELASTOSIL® E43 N TRANSPARENT is suitable for uses under the Recommendation "XV. Silicones" of the BfR and 21 CFR § 175.300 "Resinous and polymeric coatings" and FDA 21 CFR §177.2600 "Rubber articles intended for repeated use", provided that any given limitations on extractable and volatile substances are observed. Residual solvents have to be completely removed from the food contact article.
Spezifische Merkmale von ELASTOSIL® E43 N TRANSPARENT
- einkomponentig
- elektrisch isolierend
- kondensationsvernetzend
- lebensmittelverträglich
- thixotropierend
- UV- & verwitterungsbeständig
Datenblätter
- Multipurpose glue, in particular for food related applications
- Typical fields of application: household appliances, mechanical engineering
This product is a ready-to-use, one-part silicone rubber which starts curing when exposed to air moisture. Typical curing characteristics are given in the table "Properties Uncured".
As RTV-1 silicones require humidity for curing, free access of air moisture to the silicone rubber is essential. Additionally, the vulcanization time of this product can be greatly reduced by increasing the level of air's relative humidity. Please note that, unlike the initial skin formation, the total curing rate of RTV-1 silicones is limited by moisture's diffusion speed in silicone rubber.
As increasing the curing temperature has just a minor effect both on the skin forming time and the curing speed, This product typically is vulcanized at room temperature. Heat curing is recommended only for applications where the silicone rubber is applied as a thin film (thickness less than 0.5 mm), because otherwise blistering is likely to occur due to the quick release of acetic acid.
After completion of the vulcanization the silicone elastomer may continuously be exposed to constantly changing climatic conditions, UV radiation and high temperature without damage. The cured product usually shows good primerless adhesion to many substrates, e.g. glass, ceramics, metals, plastics and powder coatings.
Detailed information about the processing of RTV-1 silicones is given in our brochure “ROOM TEMPERATURE VULCANIZING (RTV) SILICONES - MATERIAL AND PROCESSING GUIDELINES”. We recommend running preliminary tests to optimize conditions for the particular application.
Removal:
If removal of the silicone from machines or dispensing equipment is necessary, white spirit or similar nonpolar solvents are recommended. However, cleaning ideally should take place before the silicone rubber is fully vulcanized. Cured silicone needs to be rubbed off or removed mechanically, if necessary in combination with a swelling agent (solvent) or a chemical silicone remover.
Lagerung
Store in a dry and cool place.
The 'Best use before end' date of each batch is shown on the product label.
Storage beyond the date specified on the label does not necessarily mean that the product is no longer usable. In this case however, the properties required for the intended use must be checked for quality assurance reasons.
Vertrieb & Support
0001 Dubai
Vereinigte Arabische Emirate
+971 4 709-9911 (Fax)
Wie können wir Ihnen helfen?
- Benötigen Sie Unterstützung bei der Produktauswahl oder wünschen Sie eine technische Beratung? Kontaktieren Sie unsere Experten.
Distributoren
WACKER verfügt weltweit über ein Netzwerk fachkundiger Vertriebspartner. Bitte wählen Sie noch eine Anwendung aus damit wir Ihnen Ihre Ansprechpartner nennen können.