This content is for Australia. Our system has detected that you are from United States. Do you want to set United States as your new country?

SILPURAN® 6700/50 A/B

SILPURAN® LR 6700 grades are self-adhesive, paste-like, easily-pigmentable two-component liquid silicone rubbers with very short curing times and good mechanical and electrical properties. Vulcanizates are noted for their self-adhesive properties to various substrates. 

 

SILPURAN® 6700/50 A/B is designed for medical applications in compliance with the WACKER SILICONES HEALTH CARE POLICY.

 


Eigenschaften

SILPURAN® 6700/50 A/B grades are a primerless, self-bonding series that adhere to various thermoplasts (e.g. PA, PBT) and metals. The bonding is improved by an ageing process (e.g. one hour at 100 °C) or by a longer storage at room temperature. Because of the individual surface properties each substrate must be tested before starting mass production. If necessary, one has to check the development of adhesive properties over time and/or in an environment relevant to the application.

 

SILPURAN® 6700/50 A/B meets selected test requirements of ISO 10993 and United States Pharmacopoeia (USP) Class VI. It is designed for medical applications in compliance with the WACKER SILICONES HEALTH CARE POLICY including implantation for < 30 days.

Spezifische Merkmale von SILPURAN® 6700/50 A/B

  • Lebensmittelkontakt
  • Reduzierter Flüchtigengehalt
  • selbsthaftend

SILPURAN® 6700 series is particularly suitable for the economical production of large series of overmolded parts (thermoplastic/elastomer), even in a comolding process (shuttle mold) under standard conditions, without any special treatment of the mold surface.

 

The following studies were performed on vulcanizates of SILPURAN® 6700/50 A/B according to ISO 10993:
    - Cytotoxicity (ISO 10993-5)
    - Sensitation LLNA (ISO 10993-10)
    - Pyrogenicity (ISO 10993-11)

The following studies were performed on vulcanizates of SILPURAN® 6700/50 A/B according to USP class VI:
    - Acute systemic toxicity
    - Intracutaneous toxicity
    - Implantation test
No adverse effects have been detected at any of the studies performed.

Properly cured and post-cured vulcanizates of SILPURAN® 6700/50 A/B can be used for food contact applications and are suitable for use under the Recommendation "XV. Silicones" of the BfR and FDA 21 CFR §177.2600 "Rubber Articles Intended for Repeated Use" considering any given limitations on extractable and volatile substances.

The A and B components are delivered ready to use in 20 kg pail kits. With adequate metering equipment, they can be pumped directly from the original containers into the injection molding machine and mixed by a static mixer. The mixing ratio is 1 : 1. At room temperature, mixtures of A and B components have a pot life of at least three days.

 

For detailed information please refer to the latest edition of our brochure "SOLID AND LIQUID SILICONE RUBBER - MATERIAL AND PROCESSING GUIDELINES".

Verpackung / Gebinde

This product is available in 20 kg pail kits. 
SILPURAN® is neither produced nor packed under sterile conditions, so the final product has to be sterilized prior to use, if necessary.

Lagerung

Once opened, containers should always be resealed after use to prevent the platinum catalyst from being poisoned by amines, sulphur or phosphorus compounds. For detailed information about storage conditions please refer to the latest edition of our brochure "SOLID AND LIQUID SILICONE RUBBER - MATERIAL AND PROCESSING GUIDELINES".
The 'Best use before end' date of each batch is shown on the product label. Storage beyond the date specified on the label does not necessarily mean that the product is no longer usable. In this case however, the properties required for the intended use must be checked for quality assurance reasons.

Vertrieb & Support

Wacker Chemicals Australia Pty.Ltd.
1 / 35 Dunlop Road
Mulgrave 3170
Australien
+61  3  9541-8900 (Phone)
+61 3 9541-8989  (Fax)
Kontakt

Wie können wir Ihnen helfen?

  • Benötigen Sie Unterstützung bei der Produktauswahl oder wünschen Sie eine technische Beratung? Kontaktieren Sie unsere Experten.
Frage stellen

Would you like a product sample?

You can request a product sample here.

Request sample

More products

Products Technical data
Appearance Aussehen Härte Shore A Reißfestigkeit Elongation at break Reißdehnung Tear strength Compression Set
ELASTOSIL® eco LR 5040/20 A/B slightly bluish slightly bluish - - 20[1] 20[1] 7.9 N/mm²[2] 7.9 N/mm²[2] - - 890 %[3] 890 %[3] 33 N/mm[6] 33 N/mm[6] - -
ELASTOSIL® eco LR 5040/30 A/B slightly bluish slightly bluish - - 30[1] 30[1] 8.6 N/mm²[2] 8.6 N/mm²[2] - - 860 %[3] 860 %[3] 32 N/mm[6] 32 N/mm[6] - -
ELASTOSIL® eco LR 5040/40 A/B slightly bluish slightly bluish - - 40[1] 40[1] 9.0 N/mm²[2] 9.0 N/mm²[2] - - 580 %[3] 580 %[3] 38 N/mm[6] 38 N/mm[6] - -
ELASTOSIL® eco LR 5040/50 A/B - - slightly bluish slightly bluish 50[1] 50[1] 9.1 N/mm²[2] 9.1 N/mm²[2] - - 490 %[3] 490 %[3] 54 N/mm[6] 54 N/mm[6] - -
ELASTOSIL® eco LR 5040/60 A/B - - slightly bluish slightly bluish 60[1] 60[1] 9.0 N/mm²[2] 9.0 N/mm²[2] - - 380 %[3] 380 %[3] 50 N/mm[6] 50 N/mm[6] - -
ELASTOSIL® eco LR 5040/70 A/B - - slightly bluish slightly bluish 70[1] 70[1] 9.5 N/mm²[2] 9.5 N/mm²[2] - - 370 %[3] 370 %[3] 36 N/mm[6] 36 N/mm[6] - -
ELASTOSIL® LR 34004/50 A/B - - white white 50[1] 50[1] 7.8 N/mm²[2] 7.8 N/mm²[2] - - 450 %[3] 450 %[3] 26 N/mm[6] 26 N/mm[6] - -
ELASTOSIL® LR 5040/20 A/B - - slightly bluish slightly bluish 20[1] 20[1] 7.9 N/mm²[2] 7.9 N/mm²[2] - - 890 %[3] 890 %[3] 33 N/mm[6] 33 N/mm[6] - -
ELASTOSIL® LR 5040/30 A/B - - slightly bluish slightly bluish 30[1] 30[1] 8.6 N/mm²[2] 8.6 N/mm²[2] - - 860 %[3] 860 %[3] 32 N/mm[6] 32 N/mm[6] - -
ELASTOSIL® LR 5040/40 A/B - - slightly bluish slightly bluish 40[1] 40[1] 9.0 N/mm²[2] 9.0 N/mm²[2] - - 580 %[3] 580 %[3] 38 N/mm[6] 38 N/mm[6] - -
ELASTOSIL® LR 5040/45 A/B - - slightly bluish slightly bluish 45[1] 45[1] 9.0 N/mm²[2] 9.0 N/mm²[2] - - 580 %[3] 580 %[3] 41 N/mm[6] 41 N/mm[6] - -
ELASTOSIL® LR 5040/50 A/B - - slightly bluish slightly bluish 50[1] 50[1] 9.1 N/mm²[2] 9.1 N/mm²[2] - - 490 %[3] 490 %[3] 54 N/mm[6] 54 N/mm[6] - -
ELASTOSIL® LR 5040/60 A/B - - slightly bluish slightly bluish 60[1] 60[1] 9.0 N/mm²[2] 9.0 N/mm²[2] - - 380 %[3] 380 %[3] 50 N/mm[6] 50 N/mm[6] - -
ELASTOSIL® LR 5040/70 A/B - - slightly bluish slightly bluish 70[1] 70[1] 9.5 N/mm²[2] 9.5 N/mm²[2] - - 370 %[3] 370 %[3] 36 N/mm[6] 36 N/mm[6] - -
SILPURAN® 6000/05 A/B transparent transparent - - 5[1] 5[1] 2.5 N/mm²[2] 2.5 N/mm²[2] - - 700 %[3] 700 %[3] 6 N/mm[6] 6 N/mm[6] - -
SILPURAN® 6000/10 A/B transparent transparent - - 10[1] 10[1] 4.2 N/mm²[2] 4.2 N/mm²[2] - - 740 %[3] 740 %[3] 13 N/mm[6] 13 N/mm[6] 15 %[7] 15 %[7]
SILPURAN® 6000/20 A/B transparent transparent - - 20[1] 20[1] 8.0 N/mm²[2] 8.0 N/mm²[2] - - 850 %[3] 850 %[3] 21 N/mm[6] 21 N/mm[6] 17 %[7] 17 %[7]
SILPURAN® 6000/30 A/B transparent transparent - - 30[1] 30[1] 8.6 N/mm²[2] 8.6 N/mm²[2] - - 650 %[3] 650 %[3] 25 N/mm[6] 25 N/mm[6] 13 %[7] 13 %[7]
SILPURAN® 6000/40 A/B - - transparent transparent 40[1] 40[1] 9.6 N/mm²[2] 9.6 N/mm²[2] - - 600 %[3] 600 %[3] 29 N/mm[6] 29 N/mm[6] 11 %[7] 11 %[7]
SILPURAN® 6000/50 A/B transparent transparent - - 50[1] 50[1] 10.0 N/mm²[2] 10.0 N/mm²[2] - - 480 %[3] 480 %[3] 30 N/mm[6] 30 N/mm[6] 14 %[7] 14 %[7]
SILPURAN® 6000/60 A/B transparent transparent - - 60[1] 60[1] 10.0 N/mm²[2] 10.0 N/mm²[2] - - 350 %[3] 350 %[3] 27 N/mm[6] 27 N/mm[6] 14 %[7] 14 %[7]
SILPURAN® 6000/70 A/B transparent transparent - - 70[1] 70[1] 9.5 N/mm²[2] 9.5 N/mm²[2] - - 290 %[3] 290 %[3] 22 N/mm[6] 22 N/mm[6] 11 %[7] 11 %[7]
SILPURAN® 6600/40 A/B transparent transparent - - 40[1] 40[1] 9.4 N/mm²[2] 9.4 N/mm²[2] - - 550 %[3] 550 %[3] 32 N/mm[6] 32 N/mm[6] 14 %[7] 14 %[7]
SILPURAN® 6600/50 A/B transparent transparent - - 50[1] 50[1] 8.9 N/mm²[2] 8.9 N/mm²[2] - - 440 %[3] 440 %[3] 31 N/mm[6] 31 N/mm[6] 13 %[7] 13 %[7]
SILPURAN® 6600/60 A/B - - transparent transparent 60[1] 60[1] 9.0 N/mm²[2] 9.0 N/mm²[2] - - 310 %[3] 310 %[3] 26 N/mm[6] 26 N/mm[6] 14 %[7] 14 %[7]
SILPURAN® 6610/40 A/B - - white white 40[1] 40[1] 7.2 N/mm²[2] 7.2 N/mm²[2] - - 510 %[3] 510 %[3] 22 N/mm[6] 22 N/mm[6] 12 %[7] 12 %[7]
SILPURAN® 6610/50 A/B - - white white 50[1] 50[1] 8.0 N/mm²[2] 8.0 N/mm²[2] - - 450 %[3] 450 %[3] 25 N/mm[6] 25 N/mm[6] 12 %[7] 12 %[7]
SILPURAN® 6610/60 A/B - - white white 60[1] 60[1] 7.0 N/mm²[2] 7.0 N/mm²[2] - - 300 %[3] 300 %[3] 20 N/mm[6] 20 N/mm[6] 15 %[7] 15 %[7]
SILPURAN® 6700/40 A/B - - transparent transparent 40[1] 40[1] 8.2 N/mm²[2] 8.2 N/mm²[2] - - 640 %[3] 640 %[3] 23 N/mm[6] 23 N/mm[6] 40 %[8] 40 %[8]
SILPURAN® 6700/50 A/B - - transparent transparent 50[1] 50[1] 8.5 N/mm²[2] 8.5 N/mm²[2] - - 590 %[3] 590 %[3] 24 N/mm[6] 24 N/mm[6] 50 %[8] 50 %[8]
SILPURAN® 6700/60 A/B - - transparent transparent 60[1] 60[1] 9.6 N/mm²[2] 9.6 N/mm²[2] - - 490 %[4] 490 %[4] 26 N/mm[6] 26 N/mm[6] 60 %[8] 60 %[8]
SILPURAN® 6740/40 A/B - - transparent transparent 40[1] 40[1] 8.8 N/mm²[2] 8.8 N/mm²[2] 710 %[5] 710 %[5] - - 27 N/mm[6] 27 N/mm[6] - -
SILPURAN® 6760/50 A/B - - transparent transparent 50[1] 50[1] 8.4 N/mm²[2] 8.4 N/mm²[2] 600 %[5] 600 %[5] - - 27 N/mm[6] 27 N/mm[6] - -
Legend
[1] Härte Shore A | DIN ISO 48-4,  [2] Reißfestigkeit | ISO 37 Type 1,  [3] Reißdehnung | ISO 37 Type 1,  [4] Reißdehnung | ISO 37 type 1,  [5] Elongation at break | ISO 37 type 1,  [6] Tear strength | ASTM D 624 B,  [7] Compression Set | 22 h | 175 °C | DIN ISO 815-1 type B method A | post-cured 6 h / 200 °C,  [8] Compression Set | 22 h | 125 °C | DIN ISO 815-1 type B method A 

Bestellen

Meine Medien


Zum Bestellformular

Vertriebskontakt

Wacker-Kemi AB
Greta Garbos väg 13, 5 th floor
16940 Solna
+46  8  5220-5220 (Phone)

Meine Favoriten

Meine Produkte