This content is for Bangladesh. Our system has detected that you are from United States. Do you want to set United States as your new country?

ELASTOSIL® SOLAR 2205

ELASTOSIL® SOLAR 2205 is a pourable addition curing RTV-2 silicone rubber for coating, lamination and encapsulation purposes. The product vulcanizes at room temperature and under heat to yield a soft elastomer.

 

Cured ELASTOSIL® SOLAR 2205 shows long-term stability against weathering, moisture and UV light. The soft silicone elastomer may continously be exposed to constantly changing climatic conditions, UV radiation and temperatures as high as 160 °C (320 °F) without damage.


Eigenschaften

Uncured:

  • very low viscosity
  • to be cured with ELASTOSIL® CAT PT, ELASTOSIL® CAT PT-F, ELASTOSIL® CAT CPV or ELASTOSIL® CAT UV as curing agent
  • 10 : 1 mixing ratio
  • fast curing at room temperature

 

 Cured:

  • soft silicone rubber (Sh 00 range)
  • crystal clear vulcanisate
  • excellent resistance to UV light
  • very high light transmission in the range of 250 nm to 1100 nm
  • recommended service temperature range: -50 °C to +160 °C

Spezifische Merkmale von ELASTOSIL® SOLAR 2205

  • elektrisch isolierend
  • hochtransparent
  • niedrige Viskosität
  • optisch klar
  • UV- & verwitterungsbeständig
  • UV-stabil
  • potting agent for the PV industry
  • encapsulation of electronic components (e.g. junction boxes or power inverters)
  • encapsulation of solar cells
  • lamination of solar modules

Surface preparation:

All surfaces must be clean and free of contaminants that will inhibit the cure of ELASTOSIL® SOLAR 2205. Examples of inhibiting contaminants are sulfur containing materials, plasticizers, urethanes, amine containing materials and organometallic compounds – especially organotin compounds. If a substrate’s ability to inhibit cure is unknown, a small scale test should be run to determine compatibility.

 

Mixing:

ELASTOSIL® SOLAR 2205 is processed with curing agents of the ELASTOSIL® CAT series. The two components need to be thoroughly mixed at a 10:1 ratio by weight or volume. Mixing can happen either manually or by automatic metering lines equipped with static or dynamic mixing devices.

 

Caution! ELASTOSIL® SOLAR 2205 contains the crosslinker, while the curing agents of the ELASTOSIL® CAT series contain the platinum catalyst. Since even traces of platinum catalyst may cause gelling of ELASTOSIL® SOLAR 2205, all tools (e.g. spatula, stirrers, mixing cups etc.) used for handling either the curing agents or the catalyzed mix must not come into contact with ELASTOSIL® SOLAR 2205 by mistake.

 

Material application:

To eliminate any air introduced during mixing, dispensing or trapped under components and devices a vacuum encapsulation is useful. Alternatively, ELASTOSIL® SOLAR 2205 and the respective curing agent can be deaerated individually prior use in order to remove absorbed air; applying a vacuum of 25-50 mbar for 10-15 min is recommended.

 

Curing:

Though curing by heat is possible, ELASTOSIL® SOLAR 2205 typically is processed at room temperature. Preferred curing agents are ELASTOSIL® CAT PT (for  a medium curing speed) and ELASTOSIL® CAT PT-F (for fast curing). When a slow curing is required, ELASTOSIL® CAT CPV can be used. Besides, ELASTOSIL® CAT UV allows a UV-activated, very fast curing of ELASTOSIL® SOLAR 2205.

 

Please note: the curing time is highly dependent on the type of curing agent used, processing temperature and both the size and the heat sink properties of the components being encapsulated. For catalyzed mixtures containing ELASTOSIL® CAT UV as curing agent, the curing speed additonally depends on irradiance and irradiation time. General information about the respective pot life is given in the table "Catalyzed".

 

Furthermore, the reactivity of ELASTOSIL® SOLAR 2205 can be adjusted within wide limits by adding WACKER® Catalyst EP or WACKER® Inhibitor PT 88 to suit the processing requirements of the particular application. WACKER® Catalyst EP increases reactivity, i. e. pot life and curing time are reduced. WACKER® Inhibitor PT 88 is a pot life extender and thus prolongs pot life and curing time.

 

Pigmentation:

ELASTOSIL® SOLAR 2205 is colourless, transparent and crystal clear. If necessary, the product can be pigmented by adding up to 2 wt. % of ELASTOSIL® COLOR PASTE FL.

 

Detailed information about processing and pigmentation is given in our brochure “ROOM TEMPERATURE VULCANIZING (RTV) SILICONES - MATERIAL AND PROCESSING GUIDELINES”. We recommend running preliminary tests to optimize conditions for the particular application.

 

Removal:

If removal of the silicone from machines or dispensing equipment is necessary, white spirit or similar nonpolar solvents are recommended. However, cleaning ideally should take place before the silicone is fully vulcanized. Cured silicone gel can be rubbed off and removed mechanically, if necessary in combination with a swelling agent (solvent).

Lagerung

Store in a dry and cool place.

 

The 'Best use before end' date of each batch is shown on the product label.

 

Storage beyond the date specified on the label does not necessarily mean that the product is no longer usable. In this case however, the properties required for the intended use must be checked for quality assurance reasons.

Vertrieb & Support

Wacker Metroark Chemicals Pvt Ltd.
D.H. Road, Chandi
Kolkata 743503
Indien
+91  33  24072-100 (Phone)
+91 33 24072-502  (Fax)
Kontakt

Wie können wir Ihnen helfen?

  • Benötigen Sie Unterstützung bei der Produktauswahl oder wünschen Sie eine technische Beratung? Kontaktieren Sie unsere Experten.
Frage stellen

Would you like a product sample?

You can request a product sample here.

Request sample

Mehr Produkte

Produkte Technische Daten
dynamische Viskosität Tear strength Weiterreißwiderstand Härte Shore A Härte Shore 00 Reißfestigkeit Reißdehnung
ELASTOSIL® RT 426 - - > 4 N/mm[1] > 4 N/mm[1] - - 60[3] 60[3] - - 4.5 N/mm²[6] 4.5 N/mm²[6] 120 %[9] 120 %[9]
ELASTOSIL® RT 563 - - 3 N/mm[1] 3 N/mm[1] - - 55[3] 55[3] - - 4.5 N/mm²[6] 4.5 N/mm²[6] 120 %[9] 120 %[9]
ELASTOSIL® RT 602 A/B 5000 mPa·s[12] 5000 mPa·s[12] - - - - 30[4] 30[4] - - 1.5 N/mm²[7] 1.5 N/mm²[7] 130 %[10] 130 %[10]
ELASTOSIL® RT 607 A/B 15000 mPa·s[13] 15000 mPa·s[13] - - - - 55[4] 55[4] - - 3 N/mm²[7] 3 N/mm²[7] 100 %[10] 100 %[10]
ELASTOSIL® RT 622 A/B 18000.0 mPa·s[14] 18000.0 mPa·s[14] - - 30 N/mm[2] 30 N/mm[2] 27[5] 27[5] - - 6.5 N/mm²[8] 6.5 N/mm²[8] 550 %[11] 550 %[11]
ELASTOSIL® SOLAR 2205 - - - - - - - - 50[16] 50[16] - - - -
SEMICOSIL® 949 UV A 150.0 mPa·s[15] 150.0 mPa·s[15] - - - - - - 40[17] 40[17] - - - -
SEMICOSIL® 949 UV B 150.0 mPa·s[15] 150.0 mPa·s[15] - - - - - - 40[17] 40[17] - - - -
Legend
[1] Tear strength | ASTM D 624 B,  [2] Weiterreißwiderstand | ASTM D 624 B,  [3] Härte Shore A | ISO 868,  [4] Härte Shore A | DIN ISO 48-4,  [5] Härte Shore A | DIN 53505 / ISO 868,  [6] Reißfestigkeit | ISO 37,  [7] Reißfestigkeit | ISO 37 Type 1,  [8] Reißfestigkeit | DIN 53504 S1 / ISO 37,  [9] Reißdehnung | ISO 37,  [10] Reißdehnung | ISO 37 Type 1,  [11] Reißdehnung | DIN 53504 S1 / ISO 37,  [12] dynamische Viskosität | 23 °C | ISO 3219,  [13] dynamische Viskosität | 23 °C | DIN EN ISO 3219,  [14] dynamische Viskosität nach Umrühren | 23 °C | DIN EN ISO 3219 | Spindle 4; 2,5 UpM; 23 °C,  [15] dynamische Viskosität | 25,0 °C | DIN EN ISO 3219,  [16] Härte Shore 00 | ASTM D 2240,  [17] Shore 00 | 23 °C | ASTM D 2240 | 10 sec 140 mW/cm² followed by 30 min 150°C 

Bestellen

Meine Medien


Zum Bestellformular

Vertriebskontakt

Wacker Kimya Ticaret Limited Şirketi
Tevfik Fikret Cad. No: 32/4
34750 Ataşehir / Istanbul
+90  216  569-7050 (Phone)

Meine Favoriten

Meine Produkte