This content is for Belgium. Our system has detected that you are from United States. Do you want to set United States as your new country?

ELASTOSIL® A316

ELASTOSIL® A316 is a free flowable, solvent-based RTV-1 silicone dispersion. It cures at room temperature or elevated temperature by reaction with air humidity to a flexible silicone coating. During cure it splits off an organic amine.


Properties

  • ready-to-use, one-component material
  • short skin-over time
  • solvent based
  • good adhesion on different substrates
  • excellent heat resistance

ELASTOSIL® A316 can be applied by dipping, spraying, brushing or coating. Thinner coatings can be obtained by addition of solvents (e.g. toluene, white spirit), thicker coatings can be realised by multiple step coating.

ELASTOSIL® A316 contains about 40% of solvent (b.w.) therefore suitable equipment has to be used and precaution measures due to the solvent vapours have to be taken. A volume shrinkage of slightly above 40% has to be considered.

ELASTOSIL® A316 is a one-part room temperature curing coating therefore the curing rate depends on temperature and on atmospheric humidity. The curing rate can be accelerated by heat exposure or exposure to carbon dioxide concentration above 1% p.b.v.

Uncured or partially cured silicone can be removed by help of organic solvents such as alipatic or aromatic hydrocarboncleaning should take place before the rubber is fully cured. Once completely cured, only mechanical removal supported by prior solvent swell is possible. Swelling can be accelerated by elevated temperature.

We recommend running preliminary tests to optimize conditions for the particular application. Comprehensive instructions are given in our leaflet "ELASTOSIL® RTV-1 Silicone Rubber".


- Protective coating against moisture and enviromental influence

- thin film coating for sealing applications

Storage

The 'Best use before end' date of each batch is shown on the product label. Storage beyond the date specified on the label does not necessarily mean that the product is no longer usable. In this case however, the properties required for the intended use must be checked for quality assurance reasons.

Sales and support

Wacker-Chemie Benelux B.V.
Heiligeweg 166
1561 DM Krommenie
Netherlands
+31  75  64760-00 (Phone)
Contact

How can we help you?

  • Do you need help in choosing a product or do you require technical support? If so, please contact our experts.
Ask a question

Would you like a product sample?

You can request a product sample here.

Request sample

More products

Products Technical data
Tear strength Viscosity, dynamic Hardness Shore A Tensile strength Elongation at break
ELASTOSIL® A234 WHITE 3.5 N/mm[1] 3.5 N/mm[1] 25000 mPa·s[3] 25000 mPa·s[3] 35[9] 35[9] 2.5 N/mm²[10] 2.5 N/mm²[10] 200 %[15] 200 %[15]
ELASTOSIL® A316 - - - - 15[9] 15[9] 0.8 N/mm²[10] 0.8 N/mm²[10] 200 %[15] 200 %[15]
ELASTOSIL® A33 IVORY 7.8 N/mm[2] 7.8 N/mm[2] 1000000 mPa·s[4] 1000000 mPa·s[4] 28[9] 28[9] 2.5 N/mm²[10] 2.5 N/mm²[10] 300 %[15] 300 %[15]
ELASTOSIL® A59 GRAY 3.0 N/mm[1] 3.0 N/mm[1] 40000 mPa·s[5] 40000 mPa·s[5] 20[9] 20[9] 1.2 N/mm²[10] 1.2 N/mm²[10] 300 %[15] 300 %[15]
ELASTOSIL® E10 ROT 8.0 N/mm[1] 8.0 N/mm[1] - - 25[9] 25[9] 2.5 N/mm²[11] 2.5 N/mm²[11] 300 %[16] 300 %[16]
ELASTOSIL® E14 Red 7 N/mm[1] 7 N/mm[1] - - 32[9] 32[9] 2.5 N/mm²[10] 2.5 N/mm²[10] 400 %[15] 400 %[15]
ELASTOSIL® E303 TRANSLUZENT - - - - 30[9] 30[9] 5 N/mm²[12] 5 N/mm²[12] 400 %[17] 400 %[17]
ELASTOSIL® E4 7.3 N/mm[1] 7.3 N/mm[1] - - 15[9] 15[9] 2 N/mm²[13] 2 N/mm²[13] 750 %[18] 750 %[18]
ELASTOSIL® E41 TRANSPARENT 11.5 N/mm[1] 11.5 N/mm[1] 100000 mPa·s[6] 100000 mPa·s[6] 40[9] 40[9] 6.0 N/mm²[13] 6.0 N/mm²[13] 350 %[18] 350 %[18]
ELASTOSIL® E43 BLACK 11.5 N/mm[1] 11.5 N/mm[1] 250000 mPa·s[3] 250000 mPa·s[3] 30[9] 30[9] 6.5 N/mm²[14] 6.5 N/mm²[14] 500 %[19] 500 %[19]
ELASTOSIL® E43 N BLACK - - - - 30[9] 30[9] 7.5 N/mm²[10] 7.5 N/mm²[10] 500 %[15] 500 %[15]
ELASTOSIL® E43 N TRANSPARENT - - - - 30[9] 30[9] 7.8 N/mm²[10] 7.8 N/mm²[10] 450 %[15] 450 %[15]
ELASTOSIL® E43 TRANSPARENT 11.5 N/mm[1] 11.5 N/mm[1] 250000 mPa·s[7] 250000 mPa·s[7] 30[9] 30[9] 6.50 N/mm²[13] 6.50 N/mm²[13] 500 %[18] 500 %[18]
ELASTOSIL® E47 TRANSPARENT 10 N/mm[1] 10 N/mm[1] 600000 mPa·s[7] 600000 mPa·s[7] 37[9] 37[9] 4.5 N/mm²[14] 4.5 N/mm²[14] 450 %[19] 450 %[19]
ELASTOSIL® E50 N TRANSPARENT - - - - 35[9] 35[9] 2.6 N/mm²[10] 2.6 N/mm²[10] 200 %[15] 200 %[15]
ELASTOSIL® E60 N BLACK - - - - 30[9] 30[9] 2.1 N/mm²[10] 2.1 N/mm²[10] 200 %[15] 200 %[15]
ELASTOSIL® E60 N GREY - - - - 32[9] 32[9] 3.0 N/mm²[10] 3.0 N/mm²[10] 250 %[15] 250 %[15]
ELASTOSIL® E60 N RED - - - - 32[9] 32[9] 3.2 N/mm²[10] 3.2 N/mm²[10] 250 %[15] 250 %[15]
ELASTOSIL® N 2010 - - 10.000 mPa·s[8] 10.000 mPa·s[8] 25[9] 25[9] 1 N/mm²[11] 1 N/mm²[11] 200 %[17] 200 %[17]
ELASTOSIL® N 2034 - - 30000 mPa·s[7] 30000 mPa·s[7] 35[9] 35[9] 2 N/mm²[11] 2 N/mm²[11] 200 %[17] 200 %[17]
ELASTOSIL® N 2076 - - - - 36[9] 36[9] 1.6 N/mm²[10] 1.6 N/mm²[10] 150 %[15] 150 %[15]
ELASTOSIL® N 2189 5.0 N/mm[1] 5.0 N/mm[1] 250000 mPa·s[7] 250000 mPa·s[7] 45[9] 45[9] 1.5 N/mm²[11] 1.5 N/mm²[11] 200 %[17] 200 %[17]
ELASTOSIL® N 2199 6.5 N/mm[1] 6.5 N/mm[1] 950000 mPa·s[3] 950000 mPa·s[3] 30[9] 30[9] 2.5 N/mm²[11] 2.5 N/mm²[11] 400 %[17] 400 %[17]
ELASTOSIL® N9111 BLACK 8.5 N/mm[2] 8.5 N/mm[2] 1000000 mPa·s[7] 1000000 mPa·s[7] 30[9] 30[9] 2.0 N/mm²[11] 2.0 N/mm²[11] 450 %[16] 450 %[16]
ELASTOSIL® N9111 GREY 10 N/mm[2] 10 N/mm[2] 1000000 mPa·s[7] 1000000 mPa·s[7] 30[9] 30[9] 2.2 N/mm²[11] 2.2 N/mm²[11] 500 %[16] 500 %[16]
ELASTOSIL® N9111 WHITE 10 N/mm[2] 10 N/mm[2] 900000 mPa·s[3] 900000 mPa·s[3] 30[9] 30[9] 2.20 N/mm²[11] 2.20 N/mm²[11] 500 %[16] 500 %[16]
ELASTOSIL® N9189 - - - - 45[9] 45[9] 2.8 N/mm²[10] 2.8 N/mm²[10] 330 %[15] 330 %[15]
Legend
[1] Tear strength | ASTM D 624 B,  [2] Tear strength | ASTM D 624 B | 23°C / 2mm,  [3] Viscosity, dynamic D = 0,5 1/s | 25 °C | DIN EN ISO 3219,  [4] Viscosity, dynamic | 25 °C | 0.5 1/s | DIN EN ISO 3219,  [5] Viscosity, dynamic | 25 °C | DIN EN ISO 3219,  [6] Viscosity, dynamic D = 1 1/s | 25 °C | DIN EN ISO 3219,  [7] Viscosity, dynamic D = 0.5 1/s | 25 °C | DIN EN ISO 3219,  [8] Viscosity, dynamic | 25 1/s | ISO 3219,  [9] Hardness Shore A | DIN ISO 48-4,  [10] Tensile strength | ISO 37 type 1,  [11] Tensile strength | ISO 37 | Type 3 / 23°C / 2mm,  [12] Tensile strength | ISO 37 | Type 3 / 23 °C / d = 2 mm,  [13] Tensile strength | ISO 37 type 1 | Type 3 / 23°C / 2mm,  [14] Tensile strength | ISO 37 type 1 | Type 3 /23°C / 2mm,  [15] Elongation at break | ISO 37 type 1,  [16] Elongation at break | ISO 37 | Type 3 / 23°C / 2mm,  [17] Elongation at break | ISO 37,  [18] Elongation at break | ISO 37 type 1 | Type 3 / 23°C / 2mm,  [19] Elongation at break | ISO 37 type 1 | Type 3 /23°C / 2mm 

Order

My media


Go to order form

Sales Contact

Wacker-Kemi AB
Greta Garbos väg 13, 5 th floor
16940 Solna
+46  8  5220-5220 (Phone)

My favorites

My products