很抱歉，本产品在United States无货。请使用产品搜索或联系 我们。

VINNAPAS® eco 5545 E (XX MB)

$VINNAPAS<sup>®</sup> eco 5545 E (XX MB)

VINNAPAS® eco 5545 E (XX MB) is a dispersible polymer powder for dry mix mortars, specifically suited for ETICS, renders and plasters. It is based on a very flexible copolymer of vinylacetate and ethylene and belongs to the product class VINNAPAS® E which means that this grade enhances machine application as well as manual application of ETICS mortars.

 

VINNAPAS® eco is a fossil resources saving product, where a specific share of the fossil-based raw materials required for manufacturing of this product can be replaced by certified sustainable renewable feedstock. The substitution is based on the REDcert² mass balance approach, audited by an independent third party.

 

The exact amount of fossil raw material replaced depends on the selected product version and is specified in the corresponding certificate. Please contact your WACKER representative or visit the product page on the WACKER website www.wacker.com for additional information regarding WACKER’s products or sustainability efforts, including mass balance.


Properties

  • VINNAPAS® eco 5545 E (XX MB) is a copolymer powder of vinyl acetate and ethylene and is dispersible in water. Because of its relatively high ethylene content, this resin is soft and flexible.
  • Its glass transition temperature (Tg) is below the freezing point of water.
  • Compounds modified with VINNAPAS® eco 5545 E (XX MB) exhibit improved adhesion, flexural strength, deformability, abrasion resistance and are easier to process. Leveling, thixotropy and water retention are essentially unaffected. The product is ideal for use in combination with other mortar additives intended to enhance specific properties.
  • VINNAPAS® eco 5545 E (XX MB) contains a fine mineral filler as an antiblocking agent.
  • It is produced without the addition of organic solvents, plasticizers and film-forming agents.
  • VINNAPAS® eco 5545 E (XX MB) has no effect on rheological properties and is a dispersible polymer powder in the lower Tg range. It is suitable for formulating highly flexible compounds with very good adhesion to organic substrates (polystyrene) and end products with low emissions.

For typical application fields of VINNAPAS® eco 5545 E (XX MB), refer to the section "application". Please discuss additional applications with your WACKER customer representative.

Processing 

For the production of ready-mixed dry mortars, such as adhesives and patching compounds, blend VINNAPAS® eco 5545 E (XX MB) with the other dry ingredients in appropriate equipment. Temperatures should not be allowed to rise excessively during mixing because otherwise the dispersible polymer powder could agglomerate by virtue of its thermoplastic properties. The mortar is prepared for use by adding the recommended amount of water and mixing mechanically or by hand. Since hand mixing generates little shear force, we recommend allowing the fresh mortar to slake for 5 minutes and then stirring it again. This is usually unnecessary where mechanical mixers are employed.


 

If the product is used in applications other than those mentioned, the choice, processing and use of it is the sole responsibility of the purchaser. All legal and other regulations must be complied with.

Slight color variations of the polymer granulate may occure without impairing the product's functionality.

Packaging

25 kg paper bags
Big Bags or bulk on request.

Storage

During storage, protect the product from contact with moisture. Prolonged storage at temperatures above 30 °C, especially in combination with pressure, humidity or exposure to sunlight, may result in blocking. Carefully seal any open containers and store them under suitable conditions. We recommend storing the product in a warehouse that provides cool and dry conditions. Do not store the product for more than six months, starting from the date at which it was received, unless the Certificate of Analysis contains a different date, which would take precedence. If the product is stored longer than recommended, it may still be used but users are advised to verify the properties required for the intended use.

Sales and support

Wacker Chemical Corporation
6870 Tilghman St
Allentown, PA 18106-9346
United States
+1  610  336-2700 (Phone)
+1 517 264-4088  (Fax)
Contact

How can we help you?

  • Do you need help in choosing a product or do you require technical support? If so, please contact our experts.
Ask a question

Would you like a product sample?

You can request a product sample here.

Request sample

Order

My media


Go to order form

Sales Contact

Wacker Chemicals (China) Co.,Ltd.
Caohejing Hi-Tech Park
200233 Shanghai
+86  21  6130-2000 （电话）

My favorites

My products