此内容适用于中国大陆。系统检测到您来自美国。您希望将 美国设置为您的新国家吗？

SILPURAN® 4200

SILPURAN® 4200 is a non-slump to self-levelling silicone rubber formulation, curing at room temperature under the influence of atmospheric moisture to a silicone elastomer exhibiting good mechanical properties.

SILPURAN® 4200 is designed for medical applications in compliance with the WACKER SILICONES HEALTH CARE POLICY.


特性

SILPURAN® 4200 meets selected test requirements of ISO 10993 and United States Pharmacopeia (USP) Class VI. It usually exhibits good primerless adhesion to many substrates, e.g. glass, ceramics, metals, plastics and powder coatings. The recommended service temperature range is approx. -50 °C to +180 °C.

SILPURAN® 4200的特殊性能

  • 单组分体系
  • 缩合固化
  • 食品接触

One-component silicone adhesive, in particular for medical applications.

The following studies were performed on vulcanizates of SILPURAN® 4200 according to ISO 10993:
    - Hemocombatibility (Hemolysis and Thrombogenicity) (ISO 10993-4)
    - Cytotoxicity (ISO 10993-5)
    - Sensitation (ISO 10993-10)
    - Pyrogenicity (ISO 10993-11)

The following studies were performed on vulcanizates of SILPURAN® 4200 according to USP class VI:
    - Acute systemic toxicity
    - Intracutaneous toxicity
    - Implantation test
No adverse effects have been detected at any of the studies performed.

Properly cured vulcanizates of SILPURAN® 4200 can be used for food contact applications and are suitable for use under the Recommendation "XV. Silicones" of the BfR as well as FDA 21 CFR § 175.300 "Resinous and polymeric coatings" and FDA 21 CFR §177.2600 "Rubber articles intended for repeated use" considering any given limitations on extractable and volatile substances.

SILPURAN® 4200 is a ready-to-use, one-part silicone rubber which starts curing when exposed to air moisture.

  -   Skin-forming time at 23 °C, 50 % RH:  5 - 10 min
  -   Curing time at 23 °C, 50 % RH: 12 h/mm

As RTV-1 silicones require humidity for curing, free access of air moisture to the silicone rubber is essential. The vulcanization time of SILPURAN® 4200 can be greatly reduced by increasing the level of air's relative humidity. Please note that, unlike the initial skin formation, the total curing rate of RTV-1 silicones is limited by moisture's diffusion speed in the silicone rubber. Since increasing the curing temperature has just a minor effect on both, the skin forming time as well as the curing speed, SILPURAN® 4200 is typically vulcanized at room temperature. Heat curing is recommended only for applications where the silicone rubber is applied as a thin film (thickness less than 0.5 mm), because otherwise blistering is likely to occur due to the quick release of acetic acid.


Detailed information about the processing of RTV-1 silicones is given in our brochure “ROOM TEMPERATURE VULCANIZING (RTV) SILICONES - MATERIAL AND PROCESSING GUIDELINES”. We recommend preliminary tests to optimize conditions for the particular application.

 


Removal:
If removal of the silicone from machines or dispensing equipment is necessary, white spirit or similar nonpolar solvents are recommended. However, cleaning ideally should take place before the silicone rubber is fully vulcanized. Cured silicone needs to be rubbed off or removed mechanically, if necessary in combination with a swelling agent (solvent) or a chemical silicone remover.

包装

SILPURAN® 4200 is available in 20 mL tubes, 310 mL cartridges and 22 kg pail kits. SILPURAN® is neither produced nor packed under sterile conditions, so the final product has to be sterilized prior to use, if necessary.

储存

Store cartridges in a dry and cool place. For storage, a minimum temperature of approx. 5 °C is recommended, temperatures below 0 °C have to be avoided. The 'Best use before end' date of each batch is shown on the product label. Storage beyond the date specified on the label does not necessarily mean that the product is no longer usable. In this case however, the properties required for the intended use must be checked for quality assurance reasons.

销售和支持

Wacker Chemicals (China) Co.,Ltd.
Caohejing Hi-Tech Park
200233 Shanghai
中国大陆
+86  21  6130-2000 （电话）
+86 21 6130-2500  （传真）
Contact Sales

我们可以为您提供什么帮助？

  • 您在选择产品方面需要帮助或者需要技术咨询？ 请联系我们的专家
Ask a question

您是否需要产品样本？

您可以在此处索取产品样本。

索取样本

经销商

未找到销售本产品的经销商

更多产品

个产品 技术数据
Tear-growth resistance 动态粘度 Shore density A Breaking strength 断裂伸长率
SILPURAN® 4200 10 N/mm[1] 10 N/mm[1] 250000 mPa·s[2] 250000 mPa·s[2] 35[3] 35[3] 5.5 N/mm²[4] 5.5 N/mm²[4] 300 %[5] 300 %[5]
说明
[1] Tear-growth resistance | ASTM D 624,  [2] 动态粘度 (0.5 s⁻ ¹) | 23 °C | DIN EN ISO 3219,  [3] Shore density A | DIN 53505 / ISO 868,  [4] Breaking strength | DIN 53504 S1 / ISO 37,  [5] 断裂伸长率 | DIN 53504 S1 / ISO 37 

购物车

我的媒体


转至订单表

联系方式

Wacker Chemicals (China) Co.,Ltd.
Caohejing Hi-Tech Park
200233 Shanghai
+86  21  6130-2000 （电话）

收藏夹

我的产品