This content is for Poland. Our system has detected that you are from United States. Do you want to set United States as your new country?

VINNAPAS® 4240 N

VINNAPAS® 4240 N  is a multi-purpose dispersible polymer powder for dry mix mortars, specifically suited for ETICS, wall applications and tile adhesives. It is based on a very flexible copolymer of vinylacetate and ethylene and belongs to the product class VINNAPAS® N which means that it has a neutral effect on rheology and provides the basic properties adhesion and flexibility. VINNAPAS® 4240 N is part of our standard range, offering you the best-in-class solutions.


Eigenschaften

  • VINNAPAS® 4240 N is a copolymer powder of vinyl acetate and ethylene and is dispersible in water.
  • Because of its relatively high ethylene content this resin is soft and flexible.
  • Its glass transition temperature (Tg) is below the freezing point of water.
  • Compounds modified with VINNAPAS® 4240 N exhibit improved adhesion, flexural strength, deformability, abrasion resistance, cohesion and are easier to process. Leveling, thixotropy and water retention are essentially unaffected. The product is ideal for use in combination with other mortar additives intended to enhance specific properties.
  • VINNAPAS® 4240 N contains a fine mineral filler as an antiblocking agent. It is produced without the addition of organic solvents, plasticizers and film-forming agents.
  • VINNAPAS® 4240 N has essentially no effect on rheological properties and is a dispersible polymer powder in the lower Tg range. It is a general-purpose powder for end products with low emissions.
  • It is suitable for formulating compounds with very good adhesion to inorganic and organic substrates, yet showing good flexibility.

For typical application fields of VINNAPAS® 4240 N, refer to the section "application". Please discuss additional applications with your WACKER customer representative.

Processing 

For the production of ready-mixed dry mortars, such as adhesives and patching compounds, blend VINNAPAS® 4240 N with the other dry ingredients in appropriate equipment. Temperatures should not be allowed to rise excessively during mixing because otherwise the dispersible polymer powder could agglomerate by virtue of its thermoplastic properties. The mortar is prepared for use by adding the recommended amount of water and mixing mechanically or by hand. Since hand mixing generates little shear force, we recommend allowing the fresh mortar to slake for 5 minutes and then stirring it again. This is usually unnecessary where mechanical mixers are employed.


 

If the product is used in applications other than those mentioned, the choice, processing and use of it is the sole responsibility of the purchaser. All legal and other regulations must be complied with.

Slight color variations of the polymer granulate may occure without impairing the product's functionality.

Verpackung / Gebinde

25 kg paper bags
Big Bags or bulk on request.

Lagerung

During storage, protect the product from contact with moisture. Prolonged storage at temperatures above 30 °C, especially in combination with pressure, humidity or exposure to sunlight, may result in blocking. Carefully seal any open containers and store them under suitable conditions. We recommend storing the product in a warehouse that provides cool and dry conditions. Do not store the product for more than six months, starting from the date at which it was received, unless the Certificate of Analysis contains a different date, which would take precedence. If the product is stored longer than recommended, it may still be used but users are advised to verify the properties required for the intended use.

Vertrieb & Support

Wacker Chemicals (South Asia)
Singapore Science Park II
117525 Singapore
Singapore
+65  6542-6638 (Phone)
+65 6542-6632  (Fax)
Kontakt

Wie können wir Ihnen helfen?

  • Benötigen Sie Unterstützung bei der Produktauswahl oder wünschen Sie eine technische Beratung? Kontaktieren Sie unsere Experten.
Frage stellen

Would you like a product sample?

You can request a product sample here.

Request sample

More products

Products Technical data
Minimum film forming temperature
VINNAPAS® 4023 N (GER) 1 °C[1] 33.8 °F[1]
VINNAPAS® 4121 N 1 °C[1] 33.8 °F[1]
VINNAPAS® 4240 N 0 °C[1] 32.0 °F[1]
VINNAPAS® 5043 N 0 °C[1] 32.0 °F[1]
VINNAPAS® 5044 N (GER) 0 °C[1] 32.0 °F[1]
VINNAPAS® 5044 N (ULS) 0 °C[1] 32.0 °F[1]
VINNAPAS® 5048 H 0 °C[1] 32.0 °F[1]
VINNAPAS® 8031 H 0 °C[1] 32.0 °F[1]
VINNAPAS® 8034 H 0 °C[1] 32.0 °F[1]
Legend
[1] Minimum film forming temperature | DIN ISO 2115 

Bestellen

Meine Medien


Zum Bestellformular

Vertriebskontakt

Wacker Chemicals Middle East
Dubai Silicon Oasis s/n
0001 Dubai
+971  4  709-9999 （电话）

Meine Favoriten

Meine Produkte