This content is for United Kingdom. Our system has detected that you are from United States. Do you want to set United States as your new country?

ELASTOSIL® eco 4000

ELASTOSIL® eco 4000 is a one-component, acid-curing, low-modulus silicone sealant with outstanding adhesion and long shelf life for construction, glazing and window application as well as industrial applications. 

ELASTOSIL® eco 4000 is produced based on a 100% exchange of fossil-based raw materials by sustainably certified renewable materials.

ELASTOSIL® eco 4000 cures at room temperature in the presence of atmospheric moisture to give a permanently flexible silicone rubber.


Properties

  • 100% silicone
  • 100% replacement of fossil-based raw materials by renewable raws.
  • non-sag
  • ready gunnability at low (+ 5 °C) and high (+ 40 °C) temperatures
  • low shrinkage on curing
  • flexible at low (-40 °C) and high temperatures (+180 °C)
  • low-modulus: better adhesion and higher safety
  • rapid crosslinking: quickly becomes tack-free
  • adheres excellently to glass, vitrified surfaces, ceramic tiles, selected plastics and most coatings
  • excellent tooling properties
  • long shelf life

Specific features of ELASTOSIL® eco 4000

  • Acetoxy-cure

Application fields

  • Glass and windows construction
  • Sealing of joints between glazing and supporting structure (frame, transoms, mullions)
  • Industrial application as sealant in the automotive, aircraft and shipbuilding industries

 

Processing

Sealant must be clean, dry and free of all loose material such as dust, dirt, rust, oil and other contaminants. Non-porous substrates should be cleaned with a solvent and a clean, lint-free, cotton cloth. Remove residual solvent before it evaporates with a fresh clean, dry cloth.

It is the user's responsibility to test the compatibility of the sealant with the adjoining materials. Incompatible substances like coating materials (paints, varnishes and glazes) or organic plasticizer containing rubbers (EPDM, butyl and neoprene) can lead to discoloration or other impairments like loss of adhesion of the sealant. Materials in direct contact with the applied sealant like cleaning agents and materials in indirect contact like gaseous emissions can damage the sealant in its function or change its appearance. Because of the multitude of these materials. Wacker cannot make a general statement to the compatibility of materials with the sealant. In case of doubt the user shall conduct appropriate preliminary tests.

The time until complete curing may be extended at lower temperature, lower humidity, increasing film thickness or by low volume of air exchange.

The use of tooling agents should be avoided if possible. Otherwise, water or a diluted solution of a little neutral soap or alcohol in water should be sparingly applied.

The work should only be carried out with sufficient fresh air supply. Wear appropriate protective clothing when processing.

 

Certification

ELASTOSIL® eco 4000 is certified and classified in accordance to

  • ISO 11600 G - Class 25 LM
  • EN 15651-1 - Class 25 LM F-INT-EXT-CC
  • EN 15651-2 - Class 25 LM G-CC
  • BS 15651-1 - Class 25 LM F-INT-EXT-CC
  • BS 15651-2 - Class 25 LM G-CC
  • DIN 18545-2 - Class E
  • ASTM C 920 - Type S, Grade NS, Class 50
  • EMICODE EC-1 PLUS
  • M1-Emission class


Adhesion

ELASTOSIL® eco 4000 exhibits excellent primerless adhesion to most non-porous siliceous substrates, e.g. glass, tiles, ceramics, enamel, glazed tiles, clinker and selected plastics as well as lacquered, glazed or impregnated wood.

Users must carry out their own tests due to the great variety of substances. The adhesion can be improved in many cases by pretreatment of the substrates with a primer. If adhesion difficulties arise please contact our technical service.

 

Restrictions in use

ELASTOSIL® eco 4000 must not be used for insulating glass applications.

ELASTOSIL® eco 4000 should not be used on substrates such as marble, concrete, fibrous cement and mortar, as the product releases acetic acid during vulcanization.

ELASTOSIL® eco 4000 should not be used in contact with metals such as lead, copper, brass or zinc due to corrosion.

ELASTOSIL® eco 4000 should not be used on substrates such as concrete, fibrous cement, and mortar, as the product releases acetic acid during.

ELASTOSIL® eco 4000 may be discolored in contact with some organic elastomers, e.g. EPDM, APTK and neoprene.

ELASTOSIL® eco 4000 is not recommended for sealing of aquaria, please use our ELASTOSIL® 4300.

ELASTOSIL® eco 4000 is not recommended for use on natural stone, such as marble, granite, quartzite, as it can cause staining.

ELASTOSIL® eco 4000 is not recommended for structural glazing bonding.

ELASTOSIL® eco 4000 is not recommended for sealing of aquaria or for longer-term use under water.

ELASTOSIL® eco 4000 is not suitable for use as a mirror adhesive.

Storage

The 'Best use before end' date of each batch is shown on the product label. Storage beyond the date specified on the label does not necessarily mean that the product is no longer usable. In this case however, the properties required for the intended use must be checked for quality assurance reasons.

Sales and support

Wacker Chemicals Ltd.
2 Arlington Square, Downshire Way
Bracknell RG12 1WA
United Kingdom
+44  1344  401 670 (Phone)
Contact

How can we help you?

  • Do you need help in choosing a product or do you require technical support? If so, please contact our experts.
Ask a question

Would you like a product sample?

You can request a product sample here.

Request sample

More products

Products Technical data
Movement capability Skin Density Modulus at 100 % elongation
ELASTOSIL® eco 4000 25 %[1] 25 %[1] 20 min[4] 20 min[4] 1.02 g/cm³[6] 8.512 lb/gal[6] 0.35 N/mm²[7] 0.35 N/mm²[7]
ELASTOSIL® eco 4100 25 %[1] 25 %[1] 20 min[4] 20 min[4] 1.02 g/cm³[6] 8.512 lb/gal[6] 0.35 N/mm²[7] 0.35 N/mm²[7]
ELASTOSIL® eco 7000 N 25 %[1] 25 %[1] 25 min[4] 25 min[4] 1.03 g/cm³[6] 8.596 lb/gal[6] 0.38 N/mm²[7] 0.38 N/mm²[7]
ELASTOSIL® eco 7100 P 25 %[1] 25 %[1] 25 min[4] 25 min[4] 1.03 g/cm³[6] 8.596 lb/gal[6] 0.38 N/mm²[7] 0.38 N/mm²[7]
ELASTOSIL® eco 7750 N 50 %[2] 50 %[2] 20 min[4] 20 min[4] 1.40 g/cm³[6] 11.684 lb/gal[6] 0.40 N/mm²[7] 0.40 N/mm²[7]
ELASTOSIL® eco 8510 P 25 %[3] 25 %[3] 15 min[5] 15 min[5] 1.02 g/cm³[6] 8.512 lb/gal[6] 0.35 N/mm²[7] 0.35 N/mm²[7]
Legend
[1] Movement capability | ISO 11600 / EN 15651,  [2] Movement capability | ASTM C920,  [3] Movement capability | ISO 11600,  [4] Skin forming time | 23 °C | 50 % r.h ,  [5] Skin formating time | 23 °C | 50 % r.h ,  [6] Density | 23 °C | ISO 1183-1 A,  [7] Modulus at 100 % elongation | ISO 8339-A 

Order

My media


Go to order form

Sales Contact

Wacker Chemicals Ltd.
2 Arlington Square, Downshire Way
Bracknell RG12 1WA
+44  1344  401 670 (Phone)

My favorites

My products