SILPURAN® 6740/40 A/B

SILPURAN® 6740/40 A/B is a paste-like, easily-pigmentable two-component liquid silicone rubber compound with short curing time. Vulcanizates are noted for their self-adhesive properties to various substrates and excellent mechanical properties. SILPURAN® 6740/40 A/B is designed for medical applications in compliance with the WACKER SILICONES HEALTH CARE POLICY including implantation for < 30 days.


Properties

SILPURAN® 6740/40 A/B meets selected test requirements of ISO 10993 and United States Pharmacopoeia (USP) Class VI. It is designed for medical applications in compliance with the WACKER SILICONES HEALTH CARE POLICY including implantation for < 30 days and is particularly suitable for the economical production of large series of injection molded articles.
SILPURAN® 6740/40 A/B is a primerless selfbonding grade that adheres to various thermoplasts (e.g. PA, PBT) and metals. The bonding is improved by an ageing process (e.g. one hour at 100 °C) or by a longer storage at room temperature. Because of the individual surface properties each substrate must be tested before starting mass production. If necessary, one has to check the development of adhesive properties over time and/or in an environment relevant to the application.

At service temperatures above approx. 180 °C the addition of heat stabilizers is recommended. Further information about an improvement of the heat stability by use of specific ELASTOSIL® Color Pastes FL can be obtained from the Technical Information Sheet "ELASTOSIL® Color Pastes FL" or the latest edition of our brochures.

Specific features of SILPURAN® 6740/40 A/B

  • Food-contact
  • High tear-resistant
  • Reduced volatile content
  • Self-adhesive

The following studies were performed on vulcanizates of SILPURAN® 6740/40 A/B according to ISO 10993:
    - Cytotoxicity (ISO 10993-5)
    - Sensitation LLNA (ISO 10993-10)
    - Pyrogenicity (ISO 10993-11)

The following studies were performed on vulcanizates of SILPURAN® 6740/40 A/B according to USP class VI:
    - Acute systemic toxicity
    - Intracutaneous toxicity
    - Implantation test
No adverse effects have been detected at any of the studies performed.

Properly cured and post-cured vulcanizates of SILPURAN® 6740/40 A/B can be used for food contact applications and are suitable for use under the Recommendation "XV. Silicones" of the BfR and FDA 21 CFR §177.2600 "Rubber Articles Intended for Repeated Use" considering any given limitations on extractable and volatile substances.

The A and B components are delivered ready to use in 20 kg pail kits. With adequate metering equipment, they can be pumped directly from the original containers into the injection molding machine and mixed by a static mixer. The mixing ratio is 1 : 1. At room temperature, mixtures of A and B components have a pot life of at least three days.

For detailed information please refer to the latest edition of our brochure "SOLID AND LIQUID SILICONE RUBBER - MATERIAL AND PROCESSING GUIDELINES".

Packaging

This product is available in 20 kg pail kits. 
SILPURAN® is neither produced nor packed under sterile conditions, so the final product has to be sterilized prior to use, if necessary.

Storage

Once opened, containers should always be resealed after use to prevent the platinum catalyst from being poisoned by amines, sulphur or phosphorus compounds. For detailed information about storage conditions please refer to the latest edition of our brochure "SOLID AND LIQUID SILICONE RUBBER - MATERIAL AND PROCESSING GUIDELINES".
The 'Best use before end' date of each batch is shown on the product label. Storage beyond the date specified on the label does not necessarily mean that the product is no longer usable. In this case however, the properties required for the intended use must be checked for quality assurance reasons.

Sales and support

Wacker Chemical Corporation
S State Road 4950
Ann Arbor, MI 48108
United States
+1  888  922-5374 (Phone)
Contact

How can we help you?

  • Do you need help in choosing a product or do you require technical support? If so, please contact our experts.
Ask a question

Would you like a product sample?

You can request a product sample here.

Request sample

More products

Products Technical data
Appearance Aussehen 外观 Shore density A Breaking strength Tensile strength Elongation at break Tear strength Compression Set
ELASTOSIL® eco LR 5040/20 A/B slightly bluish slightly bluish - - - - 20[3] 20[3] 7.9 N/mm²[5] 7.9 N/mm²[5] - - 890 %[7] 890 %[7] 33 N/mm[9] 33 N/mm[9] - -
ELASTOSIL® eco LR 5040/30 A/B slightly bluish slightly bluish - - - - 30[3] 30[3] 8.6 N/mm²[5] 8.6 N/mm²[5] - - 860 %[7] 860 %[7] 32 N/mm[9] 32 N/mm[9] - -
ELASTOSIL® eco LR 5040/40 A/B slightly bluish slightly bluish - - - - 40[3] 40[3] 9.0 N/mm²[5] 9.0 N/mm²[5] - - 580 %[7] 580 %[7] 38 N/mm[9] 38 N/mm[9] - -
ELASTOSIL® eco LR 5040/50 A/B slightly bluish slightly bluish - - - - 50[3] 50[3] 9.1 N/mm²[5] 9.1 N/mm²[5] - - 490 %[7] 490 %[7] 54 N/mm[9] 54 N/mm[9] - -
ELASTOSIL® eco LR 5040/60 A/B slightly bluish slightly bluish - - - - 60[3] 60[3] 9.0 N/mm²[5] 9.0 N/mm²[5] - - 380 %[7] 380 %[7] 50 N/mm[9] 50 N/mm[9] - -
ELASTOSIL® eco LR 5040/70 A/B slightly bluish slightly bluish - - - - 70[3] 70[3] 9.5 N/mm²[5] 9.5 N/mm²[5] - - 370 %[7] 370 %[7] 36 N/mm[9] 36 N/mm[9] - -
ELASTOSIL® LR 3003/50 US A/B Transparent[1] Transparent[1] - - - - 51 51 - - - - - - 35 kN/m 35 kN/m - -
ELASTOSIL® LR 3003/60 US A/B transparent[2] transparent[2] - - - - 59[4] 59[4] - - - - 420 %[8] 420 %[8] 31 kN/m[10] 31 kN/m[10] - -
ELASTOSIL® LR 3003/70 US A/B transparent[2] transparent[2] - - - - 68[4] 68[4] - - - - - - 31 kN/m[10] 31 kN/m[10] 18 %[11] 18 %[11]
ELASTOSIL® LR 3003/80 US A/B transparent[2] transparent[2] - - - - 77[4] 77[4] - - - - 300 %[8] 300 %[8] 21 N/mm[10] 21 N/mm[10] - -
ELASTOSIL® LR 34004/50 A/B white white - - - - 50[3] 50[3] 7.8 N/mm²[5] 7.8 N/mm²[5] - - 450 %[7] 450 %[7] 26 N/mm[9] 26 N/mm[9] - -
ELASTOSIL® LR 5040/20 A/B slightly bluish slightly bluish - - - - 20[3] 20[3] 7.9 N/mm²[5] 7.9 N/mm²[5] - - 890 %[7] 890 %[7] 33 N/mm[9] 33 N/mm[9] - -
ELASTOSIL® LR 5040/30 A/B slightly bluish slightly bluish - - - - 30[3] 30[3] 8.6 N/mm²[5] 8.6 N/mm²[5] - - 860 %[7] 860 %[7] 32 N/mm[9] 32 N/mm[9] - -
ELASTOSIL® LR 5040/40 A/B slightly bluish slightly bluish - - - - 40[3] 40[3] 9.0 N/mm²[5] 9.0 N/mm²[5] - - 580 %[7] 580 %[7] 38 N/mm[9] 38 N/mm[9] - -
ELASTOSIL® LR 5040/45 A/B slightly bluish slightly bluish - - - - 45[3] 45[3] 9.0 N/mm²[5] 9.0 N/mm²[5] - - 580 %[7] 580 %[7] 41 N/mm[9] 41 N/mm[9] - -
ELASTOSIL® LR 5040/50 A/B slightly bluish slightly bluish - - - - 50[3] 50[3] 9.1 N/mm²[5] 9.1 N/mm²[5] - - 490 %[7] 490 %[7] 54 N/mm[9] 54 N/mm[9] - -
ELASTOSIL® LR 5040/60 A/B slightly bluish slightly bluish - - - - 60[3] 60[3] 9.0 N/mm²[5] 9.0 N/mm²[5] - - 380 %[7] 380 %[7] 50 N/mm[9] 50 N/mm[9] - -
ELASTOSIL® LR 5040/70 A/B slightly bluish slightly bluish - - - - 70[3] 70[3] 9.5 N/mm²[5] 9.5 N/mm²[5] - - 370 %[7] 370 %[7] 36 N/mm[9] 36 N/mm[9] - -
SILPURAN® 6000/05 A/B transparent transparent - - - - 5[3] 5[3] 2.5 N/mm²[5] 2.5 N/mm²[5] - - 700 %[7] 700 %[7] 6 N/mm[9] 6 N/mm[9] - -
SILPURAN® 6000/10 A/B transparent transparent - - - - 10[3] 10[3] 4.2 N/mm²[5] 4.2 N/mm²[5] - - 740 %[7] 740 %[7] 13 N/mm[9] 13 N/mm[9] 15 %[12] 15 %[12]
SILPURAN® 6000/20 A/B transparent transparent - - - - 20[3] 20[3] 8.0 N/mm²[5] 8.0 N/mm²[5] - - 850 %[7] 850 %[7] 21 N/mm[9] 21 N/mm[9] 17 %[12] 17 %[12]
SILPURAN® 6000/30 A/B transparent transparent - - - - 30[3] 30[3] 8.6 N/mm²[5] 8.6 N/mm²[5] - - 650 %[7] 650 %[7] 25 N/mm[9] 25 N/mm[9] 13 %[12] 13 %[12]
SILPURAN® 6000/40 A/B transparent transparent - - - - 40[3] 40[3] 9.6 N/mm²[5] 9.6 N/mm²[5] - - 600 %[7] 600 %[7] 29 N/mm[9] 29 N/mm[9] 11 %[12] 11 %[12]
SILPURAN® 6000/50 A/B transparent transparent - - - - 50[3] 50[3] 10.0 N/mm²[5] 10.0 N/mm²[5] - - 480 %[7] 480 %[7] 30 N/mm[9] 30 N/mm[9] 14 %[12] 14 %[12]
SILPURAN® 6000/60 A/B - - transparent transparent - - 60[3] 60[3] 10.0 N/mm²[5] 10.0 N/mm²[5] - - 350 %[7] 350 %[7] 27 N/mm[9] 27 N/mm[9] 14 %[12] 14 %[12]
SILPURAN® 6000/70 A/B - - transparent transparent - - 70[3] 70[3] 9.5 N/mm²[5] 9.5 N/mm²[5] - - 290 %[7] 290 %[7] 22 N/mm[9] 22 N/mm[9] 11 %[12] 11 %[12]
SILPURAN® 6600/40 A/B - - transparent transparent - - 40[3] 40[3] 9.4 N/mm²[5] 9.4 N/mm²[5] - - 550 %[7] 550 %[7] 32 N/mm[9] 32 N/mm[9] 14 %[12] 14 %[12]
SILPURAN® 6600/50 A/B - - transparent transparent - - 50[3] 50[3] 8.9 N/mm²[5] 8.9 N/mm²[5] - - 440 %[7] 440 %[7] 31 N/mm[9] 31 N/mm[9] 13 %[12] 13 %[12]
SILPURAN® 6600/60 A/B - - transparent transparent - - 60[3] 60[3] 9.0 N/mm²[5] 9.0 N/mm²[5] - - 310 %[7] 310 %[7] 26 N/mm[9] 26 N/mm[9] 14 %[12] 14 %[12]
SILPURAN® 6610/40 A/B white white - - - - 40[3] 40[3] 7.2 N/mm²[5] 7.2 N/mm²[5] - - 510 %[7] 510 %[7] 22 N/mm[9] 22 N/mm[9] 12 %[12] 12 %[12]
SILPURAN® 6610/50 A/B white white - - - - 50[3] 50[3] 8.0 N/mm²[5] 8.0 N/mm²[5] - - 450 %[7] 450 %[7] 25 N/mm[9] 25 N/mm[9] 12 %[12] 12 %[12]
SILPURAN® 6610/60 A/B white white - - - - 60[3] 60[3] 7.0 N/mm²[5] 7.0 N/mm²[5] - - 300 %[7] 300 %[7] 20 N/mm[9] 20 N/mm[9] 15 %[12] 15 %[12]
SILPURAN® 6700/40 A/B transparent transparent - - - - 40[3] 40[3] - - 8.2 N/mm²[6] 8.2 N/mm²[6] 640 %[7] 640 %[7] 23 N/mm[9] 23 N/mm[9] 40 %[13] 40 %[13]
SILPURAN® 6700/50 A/B transparent transparent - - - - 50[3] 50[3] - - 8.5 N/mm²[6] 8.5 N/mm²[6] 590 %[7] 590 %[7] 24 N/mm[9] 24 N/mm[9] 50 %[13] 50 %[13]
SILPURAN® 6700/60 A/B - - - - transparent transparent 60[3] 60[3] - - 9.6 N/mm²[6] 9.6 N/mm²[6] 490 %[7] 490 %[7] 26 N/mm[9] 26 N/mm[9] 60 %[13] 60 %[13]
SILPURAN® 6740/40 A/B - - - - transparent transparent 40[3] 40[3] - - 8.8 N/mm²[6] 8.8 N/mm²[6] 710 %[7] 710 %[7] 27 N/mm[9] 27 N/mm[9] - -
SILPURAN® 6760/50 A/B - - - - transparent transparent 50[3] 50[3] - - 8.4 N/mm²[6] 8.4 N/mm²[6] 600 %[7] 600 %[7] 27 N/mm[9] 27 N/mm[9] - -
Legend
[1] Appearance | WSTM 2298,  [2] Appearance | DIN ISO 2137,  [3] Shore density A | DIN ISO 48-4,  [4] Shore density A | ASTM D 2240 Type A,  [5] Breaking strength | ISO 37 type 1,  [6] Tensile strength | ISO 37 type 1,  [7] Elongation at break | ISO 37 type 1,  [8] Elongation at break | ASTM D 412,  [9] Tear strength | ASTM D 624 B,  [10] Tear strength | ASTM D 624, Die B,  [11] Compression Set | 22 h | 177 °C | WSTM 1114,  [12] Compression Set | 22 h | 175 °C | DIN ISO 815-1 type B method A | post-cured 6 h / 200 °C,  [13] Compression Set | 22 h | 125 °C | DIN ISO 815-1 type B method A 

Order

My media


Go to order form

Sales Contact

Wacker Chemical Corporation
S State Road 4950
Ann Arbor, MI 48108
+1  888  922-5374 (Phone)

My favorites

My products