此内容适用于乌干达。系统检测到您来自美国。您希望将 美国设置为您的新国家吗?

ELASTOSIL® RT 708

ELASTOSIL® RT 708 is a self-levelling, slightly thixotropic, one-part heat-curing silicone for potting and coating applications. When applied in thin layer, e.g. by silk-screen printing, it also can be used as surface adhesive.

 

Cured ELASTOSIL® RT 708 shows very good adhesion to many substrates and long-term stability against weathering, moisture and UV light. The cured silicone rubber may continuously be exposed to constantly changing climatic conditions, UV radiation and temperatures as high as 230 °C (446 °F) without damage.



Eigenschaften

  • High extrusion rate
  • Self-levelling
  • Suitable for silk-screen printing
  • Fast curing at elevated temperature
  • Equipped with an UV-active fluorescent tracer for optimized process control
  • recommended service temperature range: -50 °C to +230 °C

Spezifische Merkmale von ELASTOSIL® RT 708

  • dampfbeständig
  • einkomponentig
  • elektrisch isolierend
  • hitzebeständig
  • niedrige Viskosität
  • selbsthaftend
  • thixotropierend
  • UV- & verwitterungsbeständig
  • Multipurpose potting and coating grade
  • Surface adhesive
  • Typical fields of application: household appliances, automotive, e-mobility and mechanical engineering

For an optimized process control ELASTOSIL® RT 708 is equipped with an UV-active fluorescent tracer, which allows optical detection of the silicone under black light. Best results are optained for black light sources having an emission maximum of 325 nm to 400 nm, while the fluorescence maximum of the tracer is between 400 nm and 475 nm.

 

Preparation:

All surfaces must be clean and free of contaminants that will inhibit the cure of ELASTOSIL® RT 708. Examples of inhibiting contaminants are sulfur containing materials, plasticizers, urethanes, amine containing materials and organometallic compounds – especially organotin compounds. If a substrate’s ability to inhibit cure is unknown, a small scale test should be run to determine compatibility.

 

To eliminate any air introduced during dispensing or trapped under components or devices a vacuum encapsulation is recommended. Alternatively, ELASTOSIL® RT 708 can be de-aerated prior to use; applying a vacuum of 25-50 mbar for 10-15 min is recommended.

 

Curing:

ELASTOSIL® RT 708 is a one-part heat-curing silicone, the curing time of which is highly dependent on temperature and on both the size and the heat sink properties of the components being potted. ELASTOSIL® RT 708 is usually cured between 140 °C and 200 °C in order to secure a quick build-up of adhesion to the respective substrate. Recommended curing temperatures and resulting curing times are given in adjacent table.

 

Detailed information about processing one-part heat-curing silicones is given in our brochure “ROOM TEMPERATURE VULCANIZING (RTV) SILICONES - MATERIAL AND PROCESSING GUIDELINES”. We recommend running preliminary tests to optimize conditions for the particular application.

 

Removal:

If removal of the silicone from machines or dispensing equipment is necessary, white spirit or similar nonpolar solvents are recommended. However, cleaning ideally should take place before the silicone is fully vulcanized. Cured silicone rubber needs to be rubbed off or removed mechanically, if necessary in combination with a swelling agent (solvent) or a chemical silicone remover.
 

Lagerung

Store in a dry and cool place.

 

The 'Best use before end' date of each batch is shown on the product label.

 

Storage beyond the date specified on the label does not necessarily mean that the product is no longer usable. In this case however, the properties required for the intended use must be checked for quality assurance reasons.

Vertrieb & Support

Wacker Chemicals Middle East
Dubai Silicon Oasis s/n
0001 Dubai
Vereinigte Arabische Emirate
+971  4  709-9999 (Phone)
+971 4 709-9911  (Fax)
Kontakt

Wie können wir Ihnen helfen?

  • Benötigen Sie Unterstützung bei der Produktauswahl oder wünschen Sie eine technische Beratung? Kontaktieren Sie unsere Experten.
Frage stellen

您是否需要产品样本?

您可以在此处索取产品样本。

索取样本

更多产品

个产品 技术数据
Shore density A Breaking strength 断裂伸长率 Tear-growth resistance
ELASTOSIL® RT 705 42[1] 42[1] 3.0 N/mm²[2] 3.0 N/mm²[2] 180 %[3] 180 %[3] 4.6 N/mm[4] 4.6 N/mm[4]
ELASTOSIL® RT 706 32[1] 32[1] 1.9 N/mm²[2] 1.9 N/mm²[2] 180 %[3] 180 %[3] 3.2 N/mm[4] 3.2 N/mm[4]
ELASTOSIL® RT 707 W 45[1] 45[1] 3.5 N/mm²[2] 3.5 N/mm²[2] 200 %[3] 200 %[3] - -
ELASTOSIL® RT 708 42[1] 42[1] 4.0 N/mm²[2] 4.0 N/mm²[2] 250 %[3] 250 %[3] 6.3 N/mm[4] 6.3 N/mm[4]
说明
[1] Shore density A | DIN ISO 48-4,  [2] Breaking strength | ISO 37 type 1,  [3] 断裂伸长率 | ISO 37 type 1,  [4] Tear-growth resistance | ASTM D 624 B 

Bestellen

Meine Medien


Vertriebskontakt

Wacker Chemie AG
Gisela-Stein-Strasse 1
81671 Munich
+49  89  6279-0 (电话)

Meine Favoriten

Meine Produkte