This content is for India. Our system has detected that you are from United States. Do you want to set United States as your new country?

This product is not available in India. Please use the product search or contact us.

VINNAPAS® 4410 L

VINNAPAS® 4410 L  is a dispersible polymer powder for dry mix mortars, specifically suited for self-leveling flooring compounds and screeds. It is based on a hard copolymer of vinylacetate and ethylene and belongs to the product class VINNAPAS® L which means that it improves the leveling and surface properties as well the stabilization of the fresh mortar.  Cured mortars with VINNAPAS® 4410 L have improved adhesion, flexural strength, deformability and abrasion resistance. 


Properties

  • VINNAPAS® 4410 L is a copolymer powder of vinyl acetate and ethylene and is dispersible in water.
  • As a polymeric binder VINNAPAS® 4410 L will provide very good workability to the fresh mortar.
  • Cured mortars with VINNAPAS® 4410 L have improved adhesion, flexibility, flexural strength, deformability and abrasion resistance.
  • VINNAPAS® 4410 L can be combined with casein or synthetic plasticizing admixtures to produce self-leveling flooring compounds and screeds.
  • VINNAPAS® 4410 L produces very smooth surfaces that are free of surface voids.
  • VINNAPAS® 4410 L contains a fine mineral filler as an antiblocking agent and is produced without the addition of organic solvents, plasticizers and film-forming agents.
  • Special features of VINNAPAS® 4410 L are its very good defoaming properties even without additional defoamer in the mortar formulation. This results in exceptionally smooth, uniform surfaces without air bubbles while also offering high abrasion resistance, flexural and compressive strength. Furthermore it allows self-leveling flooring compounds to be formulated with a low content of volatile organic compounds (VOC). The product thus can be used to produce self-leveling flooring compounds conforming to strict eco-labeling requirements.

Specific features of VINNAPAS® 4410 L

  • Defoaming
  • Stabilizing

For typical application fields of VINNAPAS® 4410 L, refer to the section "application". Please discuss additional applications with your WACKER customer representative.

Processing 

For the production of ready-mixed dry mortars, such as adhesives and patching compounds, blend VINNAPAS® 4410 L with the other dry ingredients in appropriate equipment. Temperatures should not be allowed to rise excessively during mixing because otherwise the dispersible polymer powder could agglomerate by virtue of its thermoplastic properties. The mortar is prepared for use by adding the recommended amount of water and mixing mechanically or by hand. Since hand mixing generates little shear force, we recommend allowing the fresh mortar to slake for 5 minutes and then stirring it again. This is usually unnecessary where mechanical mixers are employed.


 

If the product is used in applications other than those mentioned, the choice, processing and use of it is the sole responsibility of the purchaser. All legal and other regulations must be complied with.

Slight color variations of the polymer granulate may occure without impairing the product's functionality.

Packaging

25 kg paper bags
Big Bags or bulk on request.

Storage

During storage, protect the product from contact with moisture. Prolonged storage at temperatures above 30 °C, especially in combination with pressure, humidity or exposure to sunlight, may result in blocking. Carefully seal any open containers and store them under suitable conditions. We recommend storing the product in a warehouse that provides cool and dry conditions. Do not store the product for more than six months, starting from the date at which it was received, unless the Certificate of Analysis contains a different date, which would take precedence. If the product is stored longer than recommended, it may still be used but users are advised to verify the properties required for the intended use.

Sales and support

Wacker Chemicals Middle East
Dubai Silicon Oasis s/n
0001 Dubai
United Arab Emirates
+971  4  709-9999 (Phone)
+971 4 709-9911  (Fax)
Contact

How can we help you?

  • Do you need help in choosing a product or do you require technical support? If so, please contact our experts.
Ask a question

Would you like a product sample?

You can request a product sample here.

Request sample

更多产品

个产品 技术数据
Minimum film forming temperature
VINNAPAS® 4220 L 4 °C[1] 39.2 °F[1]
VINNAPAS® 4410 L 4 °C[1] 39.2 °F[1]
VINNAPAS® 5023 L 4 °C[1] 39.2 °F[1]
VINNAPAS® 5025 L 4 °C[1] 39.2 °F[1]
VINNAPAS® 5111 L 4 °C[1] 39.2 °F[1]
VINNAPAS® 5129 L 4 °C[1] 39.2 °F[1]
VINNAPAS® 5222 L 4 °C[1] 39.2 °F[1]
VINNAPAS® 7016 F 7 °C[1] 44.6 °F[1]
说明
[1] Minimum film forming temperature | DIN ISO 2115 

Order

My media


Go to order form

Sales Contact

Wacker Chemie India Pvt. Ltd.
Goregaon E,
Mumbai 400063
+91  22  42365-500 (Phone)

My favorites

My products